EPOCH 48V 100Ah V2 Elite Series – Heated & Bluetooth & Victron Comms LiFePO4 Battery

DescriptionDESCRIPTION LiFePO4 ChemistryGroup 8D Size (20.9″ x 8.7″ x 12.1″) L x W x H100Ah Capacity150A Max Continuous Discharge (300A 30s Discharge)150A Max Continuous Charge (300A 10s Charge)IP67 Rated, Dust and WATERPROOFHEATED – Internal heating for below 0C chargingBLUETOOTH – iOS and Android AppsCANBUS Communication allows BMS to communicate directly with Victron OSMountable ON/OFF SwitchMountable Battery gaugeBuilt-in Smart Battery Management System (BMS)Internal fuse with current and temperature protectionsOver charge and over discharge protectionOver current and short circuit protectionHigh & low temperature disconnects3500 Cycle life & Maintenance-free11 Year Manufacturer Warranty  SPECIFICATIONS  ConfigurationCell Configuration: 16S1P Chemistry: LiFePO4 CurrentAh Capacity: 100Ah Max Continuous Discharge Amps: 150A Max Charge Current Amps: 150A Max Discharge Peak Current Amps: 300A @ 30sec Series | Parallel: Max (16) in Parallel, Plug & Play VoltageVoltage: 51.2V Max Charge Voltage: 58.4V Operating Voltage Range: 48.0V – 58.4V TemperatureCharge Temp Range: -30°C (-22°F) / 55°C (131°F) (with heating) Discharge Temp Range: -20°C (-4°F) / 55°C (131°F) Storage Temp: -20°C (-4°F) / 45°C (113°F)   WEIGHT AND DIMENSIONS  Weight: 97 lbsDIMENSIONSLength: 20.75 (inches) Width: 8.5 (inches) Height: 12 (inches)   RECOMMENDED CHARGING SETTINGS  Batteries employed in non-Victron systems should utilize the following settings:Absorption voltage of 56.8V with an absorption time of a minimum of 15 minutes per battery.Float voltage of 54.0VEqualization offNo temperature compensationTo use the V2 Elite with Victron systems. Set up the battery comm harness and gauge as follows:Plug with waterproof bung plugged into master blue port.RJ45 cable out of master black port and into slave1 blue port.RJ45 cable out of slave1 black port and into slave blue port and so on to daisy chain up to 16 batteries in parallel.Set dips as per manual.Plug in grey RJ45 plug into the Cerbo or Ekrano GX BMS CAN port or if you have the new Cerbo Mk2 plug grey plug inot VE-CAN1 or VE-CAN 2 and change the VE can port speed to 500KBPS LV.To confirm proper reporting, go to the GX/touch screen and confirm the Epoch battery shows up on the device list. Click on the battery line, go to Details. Check to see the number of modules online is equal to the number of batteries installed. Check that the number of AH is equal to the number of AH installed.In the GX device/touch screen turn on DVCC, set controlling BMS to Epoch, set battery monitor to Epoch.The system should say External Control on the GX touch screen Inverter tile when charging (but not while inverting). The system will automatically cycle to 56.8V with an absorption time of a minimum of roughly 15 minutes per battery followed by 54.0V float voltage.It is recommended to manually program the Multiplus, Quattro and all other charge source to these same parameters in case of CAN communication loss. Over time there will be additional refinements and improvements as needed.   IP RATING IP67Experience worry-free adventures with our robust IP67 protection. Your battery is completely sealed against dust and can be safely immersed in water up to 1 meter deep for 30 minutes. Whether you’re caught in heavy rain or crossing streams, this military-grade protection ensures your power stays reliable.Fully DustproofWaterproof up to 1mAll-Weather ProtectionSubmersible Design